Zobrazit minimální záznam

dc.contributor.advisorMaršálek, Miroslav
dc.contributor.authorBartoková, Markéta
dc.date.accessioned2021-11-30T10:39:22Z
dc.date.available2021-11-30T10:39:22Z
dc.date.issued2013
dc.date.submitted2013-04-12
dc.identifier.urihttps://dspace.jcu.cz/handle/20.500.14390/11724
dc.description.abstractFríský kůň pochází ze severu Nizozemí, odkud se k nám po roce 1990 začal dovážet. Největší zásluhu na rozvoji chovu fríských koní v ČR měl v roce 1996 hřebčín v Pecínově u Benešova. Fríský kůň se dodnes chová ve třech typech, z nichž nejpočetnějším typem je střední (univerzální). Fríský kůň musí ve třech letech splňovat několik předpokladů pro zařazení do chovu. Nejvíce se při výběru hodnotí exteriér, chody a doklady o jeho původu. Hlavní plemenná kniha je vedena v Nizozemsku, u nás je pouze asociace, která registruje fríské koně na území ČR. Fríský kůň se využívá v drezúře, do zápřehu, k rekreaci a show. Bakalářská práce se zabývala rozmístěním a využitím fríských koní na území České republiky. Pomocí biometrických metod byli změřeni jedinci tohoto plemene za účelem zjištění jejich tělesných rozměrů a využití. V České republice se v roce 2012 chovalo 601 fríských koní, nejvíce byly zastoupeny klisny (406 kusů). V této práci byly u 53 koní změřeny čtyři základní tělesné rozměry. Průměrná kohoutková výška hůlková těchto koní byla 164,1 cm u hřebců, 160,9 cm u klisen a 163,7 u valachů. Tento rozměr je jediný, který je stěžejní pro zápis fríských koní do plemenné knihy. Bylo zjištěno, že nejvíce koní se využívá k rekreačnímu ježdění.cze
dc.format59 s. (57 944 znaků).
dc.format59 s. (57 944 znaků).
dc.language.isocze
dc.publisherJihočeská univerzitacze
dc.rightsBez omezení
dc.subjectfríský kůňcze
dc.subjecttělesné rozměrycze
dc.subjectvyužitícze
dc.subjectrozmístěnícze
dc.subjectfriesian horseeng
dc.subjectbody measurementseng
dc.subjectuseeng
dc.subjectdistributioneng
dc.titleRozmístění a využití fríských koní na území České republikycze
dc.title.alternativeDistribution and exploitation of friesian horses in the Czech Republiceng
dc.typebakalářská prácecze
dc.identifier.stag27847
dc.description.abstract-translatedThe friesian horse comes from the north of the Netherlands, from where it began to be imported after 1990. In 1996, the greatest merit in the development of its breeding in the Czech Republic was due to the stud in Pecinov near Benešov. The Friesian horse hase been bred in three types, the most frequent of which is the medium (universal) one. At its age of 3, the friesian horse hase to filfill a few preconditions to be included in the breed. These are, in the thirst place, its exteriér, wals of gait and the documentation of its origin. The main breeding book is kept in the Netherlands, while in this country there exists only an association registering the friesian horses within the Czech Repulick. The friesian horse is used in the dressage, harness, recreation and shows. The baccalaureate work deals with the distribution and use of the friesian horse on the territory of CR. By means of biometrical methods invidual horses have been measured in order to find out data about ther physiognomy and futher use. In 2012, 601 friesian horses were bred in the CR, mostly represented by mares (406). The basic body measurements of 53 horses have been taken. The average stick withers were 164,1 cm (stallions), 160,9 cm (mares) and 163,7 cm (geldings). This measurement is the only one which is the key for the horse to be entered into the breeding book. It has been found out that most horses are used for recreational sport.eng
dc.date.accepted2013-06-10
dc.description.departmentZemědělská fakultacze
dc.thesis.degree-disciplineZootechnikacze
dc.thesis.degree-grantorJihočeská univerzita. Zemědělská fakultacze
dc.thesis.degree-nameBc.
dc.thesis.degree-programZootechnikacze
dc.description.gradeDokončená práce s úspěšnou obhajoboucze


Soubory tohoto záznamu

Thumbnail
Thumbnail
Thumbnail
Thumbnail

Tento záznam se objevuje v

Zobrazit minimální záznam